![]() Find the port forwarding configuration page on your router.For more information, see the documentation for your router. Some routers include a default user name, password, and IP address on the underside of the router. If necessary, type your user name and password to log on to the configuration Web page.Usually the Web page is at the IP address of your router. Open your Web browser, and then connect to the configuration Web page for your router.If your router does not support the UPnP standard, you must manually configure your router to forward the following ports to the IP address of your Windows SBS 2011 Essentials server: If your router does not support UPnP, or if UPnP is disabled, there red warning that the wizard could not set up the router when Windows SBS 2011 Essentials attempts to configure your router. Follow the below guidance for each router and then close the wizard. I want to set up my router manually." and click next. Go back to setup the router and click on "Skip router setup. Click I want to skip the listed issues for now and run the wizard again later and click next. You will now need to manually set up your router if it cannot enable the ports. If it is unsuccessful a warning will be shown: If it is successful it will have set up the ports it needs and enable the Web site. Once the wizard begins, it will attempt to set up your router using UPnP. It is important to note that once the UPnP feature has been used to configure the router you can disable the UPnP feature should you so desire.īegin the wizard by clicking on Set up Remote Web Access. If your router needs to restart, wait until it restarts completely before you proceed. Save the configuration on your router, and then close the browser. The following links provide information on small business networking: If the terms ping, static IP address, DHCP, firewall ports, and UPnP are a foreign language for you, consider having a friend or consultant help you set up your network. This article assumes you have a basic understanding of small business networking. A home or small business server: provides file sharing and remote access.Multiple switches may be used if you connect more than a few desktop and notebook computers. Client computers: connect to each other through a switch (sometimes part of the router) and to the Internet through the broadband router.The router may also function as a wireless access point. Some routers support UPnP to simplify configuration. Small business routers usually provide firewall services requiring port configuration. A broadband router: a device that routes network traffic from your local network to the Internet.Some ISPs provide a device that combines a modem with a broadband router. ![]() An Internet connection device: usually a cable or DSL modem provided by your ISP.An Internet connection: provided by your Internet Service Provider (ISP).The following is a diagram of a typical home or small business network.Ī typical home or small business network consists of the following: You should verify any settings in this document to ensure your router is properly directing and filtering Internet traffic as desired. Note: this article was written for Windows SBS 2011 Essentials specifically. ![]() If your router is not listed, use the General Directions. This article covers router setup for Windows Small Business Server 2011 Essentials.ĭirections are provided for the following routers. ![]() Email, Internet access, remote access, and other services require ports to be opened and forwarded to function successfully. Proper inflow and outflow of network traffic requires careful setup of the device that directs the traffic - your router. Source: Been supporting sonicwalls for over 10 years.Windows Small Business Server 2011 Essentials: Router Setup Traffic coming from the external IP, using the service object/group, will be allowed to go to the private IP. The rule is basically the same as in NAT. Lastly, go into your Firewall settings and create a new rule for traffic coming from WAN to LAN. Make another rule with the reverse (Traffic out of the private IP, using the service group, translates as the public IP). Then, go to NAT Rules and create a new rule that will take any traffic coming from your public IP address object, using the service object/group you created, and translate it as the private IP address object. The 2nd object will be the external IP address you want the outside world to use to access your server. The first object will be the private server IP that probably lives in the LAN zone (if you haven't configured different zones). If using more than one port range, create an service group and add all the service objects your server will use.Ĭreate two address objects. Create another one if you also need UDP ports. Create an service object that includes the TCP ports you want to forward. ![]()
0 Comments
Leave a Reply. |